McGrath 18V battery pack with USB-C port and LED battery gauge

McGrath 18V Rechargeable Battery Pack - Direct Replacement for Gotoh Dual Battery Box

$250.00
Skip to product information
McGrath 18V battery pack with USB-C port and LED battery gauge

McGrath 18V Rechargeable Battery Pack - Direct Replacement for Gotoh Dual Battery Box

$250.00

Pre-order now: ships after NAMM. This is a pre-order. You pay today and we ship after the NAMM show in January 2027. We'll email you when yours is on its way.

About the photos: We're not showing the back of the board on purpose. That's where most of the design work is, so we're keeping it under wraps for now.

Direct replacement for the Gotoh dual battery box. It drops straight into the same cavity, with no routing and no soldering.

Clean 18V for your preamp. Charges from USB-C, so you never buy another 9V battery.

The McGrath 18V pack replaces the 9V batteries in your active bass with two rechargeable lithium cells. It gives a steady, low-noise 18V supply to your onboard preamp. Press the button to see how much charge is left, plug any USB-C charger in to top it up, and use the same USB-C port to connect the McGrath app to your McGrath electronics. It's a direct drop-in replacement for the Gotoh dual battery box, and you install it without any soldering.

Batteries not included. The pack is designed for two Blomiky 3.7V 1600 mAh 14500 Li-ion cells with JST plug: buy them here on Amazon.

Features

  • Easy install, no soldering: The cells plug into keyed connectors that only fit one way, and two releasable ties hold them in place. You can open and refit the ties by hand.
  • Rechargeable over USB-C: It charges from any USB-C phone charger in about 3 to 3.5 hours from empty, and a blue light stays on while it charges.
  • Long playing time: About 70 hours per charge with a typical 3 mA preamp (calculated estimate).
  • Battery gauge at the press of a button: Four LEDs light up from left to right to show the charge level, then fade back out. Each LED is about a quarter of a full charge.
  • Low-battery warning: Below 10%, the first LED gives a short flash about every 30 seconds, so you know to charge before the next gig.
  • Clean, quiet 18V: The output is filtered and runs through a low-noise regulator, so there's no hum or whine from the power stage.
  • Switched by your jack: The pack turns on when you plug a cable into the bass and turns off when you unplug it, just like a normal active bass battery.
  • USB pass-through for McGrath electronics: Plug an Android phone, tablet or computer into the pack's USB-C port and the McGrath app reaches your McGrath 12-way and McGrath 3-band preamp through it. You don't need to open the bass.
  • Protection built in:
    • Each cell is protected separately against overcharging, running flat and short circuits.
    • The USB port has surge protection and a resettable fuse.
    • The pack shuts its output off cleanly before the cells run too low.
    • It charges each cell slightly below its maximum voltage, so the cells last longer.

Playing time and charging

McGrath 18V battery pack estimated playing time per charge with 1600 mAh cells versus preamp current draw

Preamp draw at 18 V Playing time per charge (1600 mAh cells)
1 mA About 95 h (60–145)
3 mA About 70 h (50–90)
5 mA About 55 h (40–65)
10 mA About 35 h (30–40)

McGrath 18V battery pack typical charge from empty with two 1600 mAh cells

Playing and charge times are calculated estimates, not bench measurements. Charging from a phone or computer is slower than from a wall charger.

Wiring

The 18 V output has three screw terminals: +18V, COMMON GND and JACK RING ON/OFF.

  • JACK RING ON/OFF goes to the ring lug of your stereo (TRS) output jack. This turns the pack on when you plug a cable in and off when you unplug it.
  • COMMON GND goes to your preamp's ground and the output jack's sleeve lug, as a separate wire from the jack ring wire.
  • +18V goes to your preamp's power input.

Installation Guide

Fitting the cells, waking the pack, wiring, the battery gauge, the app and troubleshooting: download the 18V pack installation guide (PDF).

Specifications

Fits Gotoh dual battery box cavity (direct drop-in replacement)
Output 18.0 V DC, for onboard preamps and active electronics. Every pack tested at 17.9 to 18.1 V before shipping
Output noise About 12 µV RMS (10 Hz – 100 kHz). Fixed 500 kHz switching, so no audio-band whine at light preamp loads
Output current For onboard preamps and active electronics, up to 200 mA. Not for pedals
On/off Switched by the output jack (on when a cable is plugged in)
Standby current About 0.15 mA with the cable unplugged
Cells 2 × 3.7 V Li-ion 14500 in series (7.4 V nominal), 1600 mAh, with JST plug. Not included
Playing time per charge About 70 hours at 3 mA, about 55 hours at 5 mA (calculated estimate)
Battery gauge 4 LEDs in 25% steps, plus a blue charging LED
Low-battery warning LED 1 flashes about every 30 s below 10%
Low-battery cutoff Output turns off cleanly before the cells run too low, and back on once they're charged
Charging USB-C, 5 V, from any USB-C charger (fast chargers work and just supply 5 V)
Charge time from empty About 3 to 3.5 hours on a wall charger (calculated)
Charge voltage 4.125 V per cell, below the 4.2 V maximum, for longer cell life
Protection Per-cell overcharge, over-discharge and short-circuit protection. Resettable battery fuse. USB-C surge clamp and ESD protection. Resettable fuse on the USB pass-through. Temperature sensor on the cells while charging
USB pass-through USB 2.0 data from the USB-C port to an internal 4-way terminal (5 V, D+, D−, GND). 5 V is only present while a charger or device is plugged in; the cells never power it
App McGrath app on Android phones and tablets and on computers, reaching the McGrath 12-way and 3-band preamp
Board 48 × 56 mm
Installation Plug-in cells and screw terminals for the 18 V output (+18V, COMMON GND, JACK RING ON/OFF) and the USB pass-through. No soldering
Cell retention 2 releasable cable ties through slots in the board

What's in the box

  • McGrath 18V rechargeable pack
  • 2 releasable cable ties
  • Installation guide
  • Batteries not included (see the recommended cells above)

FAQ

When will my pre-order ship?
After the NAMM show in January 2027. We'll email you when it ships.

Will it fit my bass?
If your bass has a Gotoh dual battery box, yes. The McGrath pack is a direct replacement and drops into the same cavity.

Are batteries included?
No. The pack is designed for two Blomiky 3.7V 1600 mAh 14500 Li-ion cells with JST plug, which you can buy here on Amazon. Buy them as a pair from the same pack.

Is it hard to install?
No, and there's no soldering. Plug the two cells into the pack's connectors, which only fit one way, and fasten the two releasable ties around them. Wire JACK RING to your output jack's ring lug and COMMON GND to your preamp's ground and the jack's sleeve lug (see Wiring above), then drop the pack into the Gotoh dual battery box cavity.

How long does a charge last?
About 70 hours of playing with a typical 3 mA preamp. Preamps that draw more will run for less time.

How do I check the battery level?
Press the button. The LEDs light up from left to right to show how much charge is left: 1 LED is up to 25%, and 4 LEDs is over 75%.

How do I charge it?
Plug any USB-C charger into the pack's USB-C port. The blue light stays on while it charges and goes off when it's full. From empty, that takes about 3 to 3.5 hours.

Will it fade out like a 9V battery when it gets low?
No. The sound stays clean right up until the pack shuts off. Watch for the low-battery flash, and press the button before a gig to check the level.

Can I use the McGrath app through the pack?
Yes, from an Android phone, an Android tablet or a computer over USB. Plug a cable into the bass's output jack first, because the 3-band preamp only powers up when a cable is in.

Can I use other cells?
Only 3.7V Li-ion 14500 cells. Never use LiFePO4 (3.2V) or NiMH cells, even though they're the same size and sometimes have the same plug. We recommend the Blomiky cells linked above.

How do I replace the cells?
Always replace both cells at the same time with a matched pair from the same pack. The battery gauge may read low for the first cycle while it relearns the new cells, so give it one full charge and one full run-down.

Can I power pedals from it?
No. The 18V output is designed for onboard preamps and active electronics only.

You may also like