If your bass suddenly feels stiff, buzzy or just not quite right, the cause is usually one of three things: the action (how high the strings sit above the frets), the neck relief (how much the neck bows forward) or the nut slots. The good news is that you can measure all three at home in a few minutes. Once you have the numbers, you know exactly what changed and whether it is a quick tweak or a job for a tech.
What you are actually measuring
- Action: the gap between the top of a fret and the bottom of the string, usually checked at the 12th fret. Lower action is easier to play; higher action buzzes less and lets you dig in harder.
- Neck relief: a slight forward bow in the neck that gives the strings room to vibrate. Too little and you get buzz in the first few frets; too much and the middle of the neck feels high and spongy.
- Nut slots: how deep each string sits at the nut. If the slots are too high, the first few frets feel hard to press and can play sharp. Too low and the open string buzzes.
How to check each one
Tune to pitch first and play in your normal position, because string tension changes everything. Then work in this order:
- Relief first. Put a capo on the 1st fret and measure at the 7th or 8th fret. Relief affects your action reading, so always set it before anything else.
- Action second. Measure string height at the 12th fret on the lowest and highest strings. A common starting point many techs use on bass is somewhere around 2 to 2.5 mm on the G string and 2.5 to 3 mm on the E (or B), then adjust to taste and playing style.
- Nut last. Zero your gauge with the string pressed to the 1st fret, then check the slot. If you are filing, you can file and recheck without zeroing again.
Write your numbers down. When your bass feels perfect, those numbers are your recipe, and you can set the next instrument up the same way.
Why we made our own gauge
Cormac built the McGrath Digital String Height Gauge for our own shop. It is based on the LMI digital gauge that is no longer made: set the base on a fret, press zero and read the gap straight off the display, in inches or millimetres.
Brass gauges are heavy, expensive and made for one string spacing. Ours has a light, open acrylic base with a digital readout, so it fits wherever the strings are, on basses, 6, 7 and 8-strings, 12-strings and mandolins. It is also safe on finishes, because there is no heavy brass block to drop on a top. Each one is cut on our CNC and engraved with the McGrath logo, and over 200 are now out in workshops.
The gauge is $50, takes one CR2032 coin cell (not included), and comes with an instructions PDF that covers how to zero and read it, what to measure where, typical starting specs for electric, acoustic and bass, and a printable setup log.
Got your spacing right too?
If you are swapping a bridge or pickups, string spacing matters as much as height. Our String Spacing Gauge covers the four most common spacings (17 mm, 18 mm, 18.5 mm and 19 mm) with grooves sized for real string gauges and center arrows to keep everything lined up with the neck and magnets.
Common questions
Can I adjust relief myself?
Small truss rod adjustments are a normal part of owning a bass, but go slowly, a little at a time, and let the neck settle. If the rod feels stuck or you are not sure, take it to a tech.
Why did my action change on its own?
Seasonal changes in temperature and humidity can move a neck. Measuring a couple of times a year tells you whether it has moved and by how much.
Do McGrath basses come set up?
Yes. Every instrument gets final assembly, full electronics testing and a complete playability setup before it leaves our San Diego shop.
Want one set up for you?
Design your own in the Bass Builder and we will set it up before it ships, or browse our in-stock instruments. Questions about your setup? Email info@mcgrathguitars.com and we are happy to help.
1 comment
Funny how the Chinese can turn everything into anything…. I bought a similar (exact same digital unit) off temu for $2.99. I few slight mods and a bulk order…. you’re asking $50 ?