McGrath push-pull volume pot board with A500K pot and screw terminals

McGrath Push-Pull Volume Pot Board - True-Bypass, 250K/500K Switchable

$69.00
Skip to product information
McGrath push-pull volume pot board with A500K pot and screw terminals

McGrath Push-Pull Volume Pot Board - True-Bypass, 250K/500K Switchable

$69.00

Pre-order now: ships after NAMM. This is a pre-order. You pay today and we ship after the NAMM show in January 2027. We'll email you when yours is on its way.

About the photos: We're not showing the back of the board on purpose. That's where most of the design work is, so we're keeping it under wraps for now.

Solderless-style volume control with true-bypass preamp switching and a switchable 250K/500K taper, all on one compact board.

The McGrath Push-Pull Volume Pot Board turns your volume control into a clean, plug-and-play hub for active/passive bass and guitar wiring. Push or pull the knob to switch your onboard preamp in or out, flip a tiny switch to choose between 500K and 250K tone, and connect everything with screw terminals instead of a mess of wires.

Features

  • True-bypass preamp switching: Both poles of the push-pull DPDT are used. Pull the knob up for passive: the pot goes straight to the jack and your preamp's input and output are fully disconnected, so it adds nothing to your passive tone. Push down for active: the signal runs through your preamp.
  • Switchable 500K / 250K, with a true audio taper in both modes: Flip the small onboard switch to choose 500K or 250K. Either way, the volume sweep stays smooth and even all the way up, with no dip in the upper range and no jump at the top. Choose 500K for a brighter, more open top end, or 250K for a warmer, smoother one.
  • Screw terminals for every connection: Labelled terminals for FROM PICKUP / TO JACK, FROM PREAMP / TO PREAMP and GROUND, plus a 3-way terminal right beside the pot's solder lugs for short, straight lug wiring. Change pickups or preamps without reaching for the iron.
  • Solid grounding: The pot body is bonded straight to the board's ground planes through a plated slot with a solid connection, so your pot can and control plate are grounded. A dedicated chassis pad gives you an easy spot for a cavity-shielding or bridge ground wire.
  • Compact and robust: A small 28 x 21.5 mm, 2-layer, 1.6 mm board that mounts directly on the pot's switch pins and body tab. Ground planes on both layers are stitched together for low noise.

Volume taper

The knob sweeps exactly the same in 500K and 250K mode. The grey line shows the usual 250K switch mod for comparison: it's about 3 dB quieter from 7 to 9, then jumps at the top.

McGrath push-pull volume pot taper in 500K and 250K mode compared with a typical 250K switch mod

Tone

A humbucker with the volume full up: about +8.5 dB of treble peak at 3.5 kHz in 500K mode, and about +5 dB in 250K mode. Bass and mids are the same in both.

Humbucker treble response in 500K and 250K mode with the McGrath volume pot

Signal path

Pulled up is passive true bypass, and pushed down puts the preamp in the path.

McGrath push-pull volume pot signal path: pulled up is passive true bypass, pushed down puts the preamp in the path

Curves are modelled from the design, not bench measurements.

Specifications

  • Pot: 500K audio (A500K) push-pull with solder lugs, Bourns PDB183 series
  • Modes: 500K or 250K (switch selectable), both audio taper
  • Preamp switching: True bypass via push-pull DPDT
  • Connections: Screw terminals for pickup, jack, preamp send/return, ground and pot lugs
  • Board size: 28 x 21.5 mm

What's in the box

  • Assembled board with A500K push-pull pot fitted

Installation Guide

Terminal-by-terminal wiring, the 250K switch and troubleshooting: download the volume pot installation guide (PDF).

You may also like