{"product_id":"mcgrath-18v-rechargeable-battery-pack-for-active-bass","title":"McGrath 18V Rechargeable Battery Pack - Direct Replacement for Gotoh Dual Battery Box","description":"\u003cp\u003e\u003cstrong\u003ePre-order now: ships after NAMM.\u003c\/strong\u003e This is a pre-order. You pay today and we ship after the NAMM show in January 2027. We'll email you when yours is on its way.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAbout the photos:\u003c\/strong\u003e We're not showing the back of the board on purpose. That's where most of the design work is, so we're keeping it under wraps for now.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDirect replacement for the Gotoh dual battery box.\u003c\/strong\u003e It drops straight into the same cavity, with no routing and no soldering.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eClean 18V for your preamp. Charges from USB-C, so you never buy another 9V battery.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe McGrath 18V pack replaces the 9V batteries in your active bass with two rechargeable lithium cells. It gives a steady, low-noise 18V supply to your onboard preamp. Press the button to see how much charge is left, plug any USB-C charger in to top it up, and use the same USB-C port to connect the McGrath app to your McGrath electronics. It's a direct drop-in replacement for the Gotoh dual battery box, and you install it without any soldering.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBatteries not included.\u003c\/strong\u003e The pack is designed for two Blomiky 3.7V 1600 mAh 14500 Li-ion cells with JST plug: \u003ca href=\"https:\/\/www.amazon.com\/dp\/B08Q45XQKW\" target=\"_blank\" rel=\"noopener\"\u003ebuy them here on Amazon\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eEasy install, no soldering:\u003c\/b\u003e The cells plug into keyed connectors that only fit one way, and two releasable ties hold them in place. You can open and refit the ties by hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eRechargeable over USB-C:\u003c\/b\u003e It charges from any USB-C phone charger in about 3 to 3.5 hours from empty, and a blue light stays on while it charges.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eLong playing time:\u003c\/b\u003e About 70 hours per charge with a typical 3 mA preamp (calculated estimate).\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eBattery gauge at the press of a button:\u003c\/b\u003e Four LEDs light up from left to right to show the charge level, then fade back out. Each LED is about a quarter of a full charge.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eLow-battery warning:\u003c\/b\u003e Below 10%, the first LED gives a short flash about every 30 seconds, so you know to charge before the next gig.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eClean, quiet 18V:\u003c\/b\u003e The output is filtered and runs through a low-noise regulator, so there's no hum or whine from the power stage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eSwitched by your jack:\u003c\/b\u003e The pack turns on when you plug a cable into the bass and turns off when you unplug it, just like a normal active bass battery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eUSB pass-through for McGrath electronics:\u003c\/b\u003e Plug an Android phone, tablet or computer into the pack's USB-C port and the McGrath app reaches your McGrath 12-way and McGrath 3-band preamp through it. You don't need to open the bass.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eProtection built in:\u003c\/b\u003e\n\u003cul\u003e\n\u003cli\u003eEach cell is protected separately against overcharging, running flat and short circuits.\u003c\/li\u003e\n\u003cli\u003eThe USB port has surge protection and a resettable fuse.\u003c\/li\u003e\n\u003cli\u003eThe pack shuts its output off cleanly before the cells run too low.\u003c\/li\u003e\n\u003cli\u003eIt charges each cell slightly below its maximum voltage, so the cells last longer.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePlaying time and charging\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0668\/6949\/3926\/files\/image_8c62dcdf-51c3-4903-a31f-cfea3d727f71.png?v=1794893124\" alt=\"McGrath 18V battery pack estimated playing time per charge with 1600 mAh cells versus preamp current draw\" width=\"2000\" height=\"1240\" loading=\"lazy\" style=\"width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003ePreamp draw at 18 V\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cb\u003ePlaying time per charge (1600 mAh cells)\u003c\/b\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e1 mA\u003c\/td\u003e\n\u003ctd\u003eAbout 95 h (60–145)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 mA\u003c\/td\u003e\n\u003ctd\u003eAbout 70 h (50–90)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e5 mA\u003c\/td\u003e\n\u003ctd\u003eAbout 55 h (40–65)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e10 mA\u003c\/td\u003e\n\u003ctd\u003eAbout 35 h (30–40)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0668\/6949\/3926\/files\/image_7a94bed4-a29f-4aca-acda-81ace11a3c9e.png?v=1794893125\" alt=\"McGrath 18V battery pack typical charge from empty with two 1600 mAh cells\" width=\"2000\" height=\"1440\" loading=\"lazy\" style=\"width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003ePlaying and charge times are calculated estimates, not bench measurements. Charging from a phone or computer is slower than from a wall charger.\u003c\/i\u003e\u003c\/p\u003e\n\u003ch3\u003eWiring\u003c\/h3\u003e\n\u003cp\u003eThe 18 V output has three screw terminals: \u003cb\u003e+18V\u003c\/b\u003e, \u003cb\u003eCOMMON GND\u003c\/b\u003e and \u003cb\u003eJACK RING ON\/OFF\u003c\/b\u003e.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eJACK RING ON\/OFF\u003c\/b\u003e goes to the ring lug of your stereo (TRS) output jack. This turns the pack on when you plug a cable in and off when you unplug it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eCOMMON GND\u003c\/b\u003e goes to your preamp's ground and the output jack's sleeve lug, as a separate wire from the jack ring wire.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003e+18V\u003c\/b\u003e goes to your preamp's power input.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation Guide\u003c\/h3\u003e\n\u003cp\u003eFitting the cells, waking the pack, wiring, the battery gauge, the app and troubleshooting: \u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0668\/6949\/3926\/files\/McGrath_18V_Pack_Install_Guide_1600mAh.pdf?v=1794893125\" target=\"_blank\" rel=\"noopener\" download\u003e\u003cstrong\u003edownload the 18V pack installation guide (PDF)\u003c\/strong\u003e\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eGotoh dual battery box cavity (direct drop-in replacement)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOutput\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e18.0 V DC, for onboard preamps and active electronics. Every pack tested at 17.9 to 18.1 V before shipping\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput noise\u003c\/td\u003e\n\u003ctd\u003eAbout 12 µV RMS (10 Hz – 100 kHz). Fixed 500 kHz switching, so no audio-band whine at light preamp loads\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput current\u003c\/td\u003e\n\u003ctd\u003eFor onboard preamps and active electronics, up to 200 mA. Not for pedals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOn\/off\u003c\/td\u003e\n\u003ctd\u003eSwitched by the output jack (on when a cable is plugged in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eStandby current\u003c\/td\u003e\n\u003ctd\u003eAbout 0.15 mA with the cable unplugged\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCells\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e2 × 3.7 V Li-ion 14500 in series (7.4 V nominal), 1600 mAh, with JST plug. Not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePlaying time per charge\u003c\/td\u003e\n\u003ctd\u003eAbout 70 hours at 3 mA, about 55 hours at 5 mA (calculated estimate)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBattery gauge\u003c\/td\u003e\n\u003ctd\u003e4 LEDs in 25% steps, plus a blue charging LED\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLow-battery warning\u003c\/td\u003e\n\u003ctd\u003eLED 1 flashes about every 30 s below 10%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLow-battery cutoff\u003c\/td\u003e\n\u003ctd\u003eOutput turns off cleanly before the cells run too low, and back on once they're charged\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCharging\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB-C, 5 V, from any USB-C charger (fast chargers work and just supply 5 V)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCharge time from empty\u003c\/td\u003e\n\u003ctd\u003eAbout 3 to 3.5 hours on a wall charger (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCharge voltage\u003c\/td\u003e\n\u003ctd\u003e4.125 V per cell, below the 4.2 V maximum, for longer cell life\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eProtection\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003ePer-cell overcharge, over-discharge and short-circuit protection. Resettable battery fuse. USB-C surge clamp and ESD protection. Resettable fuse on the USB pass-through. Temperature sensor on the cells while charging\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eUSB pass-through\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 data from the USB-C port to an internal 4-way terminal (5 V, D+, D−, GND). 5 V is only present while a charger or device is plugged in; the cells never power it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApp\u003c\/td\u003e\n\u003ctd\u003eMcGrath app on Android phones and tablets and on computers, reaching the McGrath 12-way and 3-band preamp\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eBoard\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e48 × 56 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInstallation\u003c\/td\u003e\n\u003ctd\u003ePlug-in cells and screw terminals for the 18 V output (+18V, COMMON GND, JACK RING ON\/OFF) and the USB pass-through. No soldering\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCell retention\u003c\/td\u003e\n\u003ctd\u003e2 releasable cable ties through slots in the board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhat's in the box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMcGrath 18V rechargeable pack\u003c\/li\u003e\n\u003cli\u003e2 releasable cable ties\u003c\/li\u003e\n\u003cli\u003eInstallation guide\u003c\/li\u003e\n\u003cli\u003eBatteries not included (see the recommended cells above)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eWhen will my pre-order ship?\u003c\/b\u003e\u003cbr\u003eAfter the NAMM show in January 2027. We'll email you when it ships.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWill it fit my bass?\u003c\/b\u003e\u003cbr\u003eIf your bass has a Gotoh dual battery box, yes. The McGrath pack is a direct replacement and drops into the same cavity.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAre batteries included?\u003c\/b\u003e\u003cbr\u003eNo. The pack is designed for two Blomiky 3.7V 1600 mAh 14500 Li-ion cells with JST plug, which you can \u003ca href=\"https:\/\/www.amazon.com\/dp\/B08Q45XQKW\" target=\"_blank\" rel=\"noopener\"\u003ebuy here on Amazon\u003c\/a\u003e. Buy them as a pair from the same pack.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eIs it hard to install?\u003c\/b\u003e\u003cbr\u003eNo, and there's no soldering. Plug the two cells into the pack's connectors, which only fit one way, and fasten the two releasable ties around them. Wire JACK RING to your output jack's ring lug and COMMON GND to your preamp's ground and the jack's sleeve lug (see Wiring above), then drop the pack into the Gotoh dual battery box cavity.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHow long does a charge last?\u003c\/b\u003e\u003cbr\u003eAbout 70 hours of playing with a typical 3 mA preamp. Preamps that draw more will run for less time.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHow do I check the battery level?\u003c\/b\u003e\u003cbr\u003ePress the button. The LEDs light up from left to right to show how much charge is left: 1 LED is up to 25%, and 4 LEDs is over 75%.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHow do I charge it?\u003c\/b\u003e\u003cbr\u003ePlug any USB-C charger into the pack's USB-C port. The blue light stays on while it charges and goes off when it's full. From empty, that takes about 3 to 3.5 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWill it fade out like a 9V battery when it gets low?\u003c\/b\u003e\u003cbr\u003eNo. The sound stays clean right up until the pack shuts off. Watch for the low-battery flash, and press the button before a gig to check the level.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCan I use the McGrath app through the pack?\u003c\/b\u003e\u003cbr\u003eYes, from an Android phone, an Android tablet or a computer over USB. Plug a cable into the bass's output jack first, because the 3-band preamp only powers up when a cable is in.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCan I use other cells?\u003c\/b\u003e\u003cbr\u003eOnly 3.7V Li-ion 14500 cells. Never use LiFePO4 (3.2V) or NiMH cells, even though they're the same size and sometimes have the same plug. We recommend the Blomiky cells linked above.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eHow do I replace the cells?\u003c\/b\u003e\u003cbr\u003eAlways replace both cells at the same time with a matched pair from the same pack. The battery gauge may read low for the first cycle while it relearns the new cells, so give it one full charge and one full run-down.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCan I power pedals from it?\u003c\/b\u003e\u003cbr\u003eNo. The 18V output is designed for onboard preamps and active electronics only.\u003c\/p\u003e","brand":"McGrath Guitars","offers":[{"title":"Default Title","offer_id":58452132102310,"sku":"MG-EL-45631142","price":250.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0668\/6949\/3926\/files\/IMG_0598_white.jpg?v=1794882625","url":"https:\/\/mcgrathguitars.com\/products\/mcgrath-18v-rechargeable-battery-pack-for-active-bass","provider":"McGrath Guitars","version":"1.0","type":"link"}